{"product_id":"general-electric-ds200qtbag1a-rst-termination-board","title":"General Electric DS200QTBAG1A RST Termination Board","description":"\u003cp\u003eThe \u003cstrong\u003eGeneral Electric DS200QTBAG1A\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eDS200QTBAG1A\u003c\/strong\u003e Termination Module, operates as a dedicated hardware component for field signal termination and core interconnection within Mark V Speedtronic turbine control platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eDS200QTBAG1A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eGeneral Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eStandard printed circuit board form factor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003eStandard Mark V enclosure profile\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003eStandard industrial cabinet range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive termination circuitry (no active power draw)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eIndustrial Control and Drive Characteristics\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eProfinet \/ EtherNet\/IP deterministic networks\u003c\/strong\u003e: The system architecture interfaces with deterministic network modules to ensure time-critical communication and synchronization across distributed turbine control nodes.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackplane bus communication velocity Licences\u003c\/strong\u003e: Integrated COREBUS connectors (JAI and JAJ) facilitate high-speed data transfer between core processors and termination hardware to minimize control loop latency.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eI\/O density scaling\u003c\/strong\u003e: Dual terminal blocks (TB1 and TB2) support up to 144 signal wires, providing high-density connection points for LVDT sensors, servo outputs, and monitoring lines.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFirmware flash compatibility\u003c\/strong\u003e: Passive termination board architecture eliminates the need for onboard firmware flashing, relying entirely on direct physical signal passthrough.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Does the RST termination board support hot-swapping within the Mark V core cabinet during turbine operation?\u003c\/p\u003e\n\u003cp\u003eA: System maintenance guidelines require powering down the associated core rack prior to disconnecting or replacing the board to prevent electrical transients and protect connected controller inputs.\u003c\/p\u003e\n\u003cp\u003eQ: How are individual signal wires identified on the terminal blocks?\u003c\/p\u003e\n\u003cp\u003eA: Each terminal is mapped using the terminal block identifier and pin number, such as TB1-66 or TB2-33, corresponding to factory documentation for specific signal routing.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMount the circuit board securely within the designated Mark V cabinet slot, ensuring proper mechanical alignment and adequate clearance for wiring harnesses.\u003c\/li\u003e\n\u003cli\u003eTerminate incoming field signal wires to the appropriate numbered screw terminals on blocks TB1 and TB2, verifying wire labels against system documentation before startup.\u003c\/li\u003e\n\u003cli\u003eRoute low-level sensor and LVDT signal cables separately from high-voltage power lines and motor drives to mitigate electromagnetic interference.\u003c\/li\u003e\n\u003cli\u003eEnsure that the board chassis grounding points are tightly bonded to the cabinet earth bar to maintain proper noise suppression and shield grounding integrity.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"GE","offers":[{"title":"Default Title","offer_id":45270659858547,"sku":"DS200QTBAG1A","price":88.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0644\/4348\/2227\/files\/DS200TBQCG1A_19ca79d2-6ef1-4e04-9c53-780126c72549.png?v=1784711623","url":"https:\/\/www.dcssupplier.com\/ar\/products\/general-electric-ds200qtbag1a-rst-termination-board","provider":"DcsSupplier Limited","version":"1.0","type":"link"}