{"product_id":"epro-con021-pr6424-000-000-vibration-sensor-system","title":"EPRO CON021+PR6424\/000-000 Vibration Sensor System","description":"\u003cp\u003eThe \u003cstrong\u003eEPRO CON021 + PR6424\/000-000\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eCON021 + PR6424\u003c\/strong\u003e Vibration Sensor System, operates as a dedicated hardware component for non-contact radial shaft vibration and displacement measurement within MMS6000 shaft monitoring platforms.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003cfigure class=\"table\"\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eCON021 + PR6424\/000-000\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eEPRO\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eGermany\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eStandard Sensor Assembly Mass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e8 mm Probe Tip Diameter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-35 to +100 deg C (CON021); Probe Cable rated to 200 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003eOperating Voltage -18 V to -30 V DC (-24 V DC Nominal)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Signal\u003c\/td\u003e\n\u003ctd\u003e-4 V to -20 V DC linear range (-1 V to -22 V full range)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSensitivity\u003c\/td\u003e\n\u003ctd\u003e-7.87 V\/mm (-200 mV\/mil)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFrequency Response\u003c\/td\u003e\n\u003ctd\u003e0 Hz to 10 kHz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProtection Rating\u003c\/td\u003e\n\u003ctd\u003eIP20 for CON021 Signal Conditioner\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eEddy-Current Probe Scaling \u0026amp; Gap Voltage Validation\u003c\/h3\u003e\n\u003cp\u003eThe combined eddy-current sensing system utilizes high-frequency electromagnetic field output from the 8 mm PR6424 probe tip to measure target movement relative to the sensor face. Internal signal conditioning inside the CON021 converter provides precise eddy-current probe scaling at -7.87 V\/mm (-200 mV\/mil) over a 0 Hz to 10 kHz frequency response spectrum. During mechanical alignment, gap voltage validation targets a nominal -12 V DC operational center point (corresponding to gap targets within the linear dynamic range), allowing accurate measurement of dynamic rotor dynamics without signal clipping.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: What is the nominal supply voltage required for the CON021 signal converter?\u003c\/p\u003e\n\u003cp\u003eA: The converter requires a nominal power supply of -24 V DC, operating within an allowable input range of -18 V to -30 V DC.\u003c\/p\u003e\n\u003cp\u003eQ: How is the physical gap zero-point validated during probe installation?\u003c\/p\u003e\n\u003cp\u003eA: Mechanical insertion depth is adjusted while observing sensor voltage until reaching a nominal gap voltage of -12 V DC on the output terminals.\u003c\/p\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eMount the PR6424 sensor head rigidly to the bearing housing to eliminate mechanical resonance in the measurement axis.\u003c\/li\u003e\n\u003cli\u003eSecure the 5 m total cable system using LEMO connector fittings, avoiding tight bend radii along the extension lead.\u003c\/li\u003e\n\u003cli\u003eMaintain minimum lateral clearance around the 8 mm probe tip to prevent side-wall crosstalk suppression issues with nearby ferrous structures.\u003c\/li\u003e\n\u003cli\u003eEnsure the CON021 signal conditioner is grounded and housed within an IP-rated enclosure to shield against industrial EMI.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Emerson Epro","offers":[{"title":"Default Title","offer_id":45464111415411,"sku":"CON021+PR6424\/000-000","price":88.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0644\/4348\/2227\/files\/CON021_PR6424002-010_2.jpg?v=1789019900","url":"https:\/\/www.dcssupplier.com\/products\/epro-con021-pr6424-000-000-vibration-sensor-system","provider":"DcsSupplier Limited","version":"1.0","type":"link"}