Allen-Bradley 1734-RTBS POINT I/O Removable Terminal Block Assembly

The Allen-Bradley 1734-RTBS, also cataloged as the 1734-RTBS Terminal Block, operates as a dedicated hardware component for field wiring termination within POINT I/O 1734 platforms.

Hardware Specifications

Backplane Signal Termination and I/O Density Scaling

• The Allen-Bradley 1734-RTBS provides direct physical execution for signal distribution across EtherNet/IP deterministic networks.
• The 8-terminal spring-clamp layout facilitates rapid field wiring termination while maintaining I/O density scaling on POINT I/O slice platforms.
• Galvanic protection between logic-side processing and field wiring pathways is maintained via a 250 V continuous isolation voltage rating.
• Seamless firmware flash compatibility across primary PLC drops is preserved through passive electrical pass-through execution.

Frequently Asked Questions

Q: Which terminal base models are compatible with the 1734-RTBS spring-clamp assembly?

A: The 1734-RTBS is designed for installation on 1734-TBS and 1734-TOPS terminal base units.

Q: What wire sizes and electrical ratings are supported by the 1734-RTBS signal terminals?

A: The spring terminals accommodate 14 to 22 AWG (0.25 to 2.5 mm2) wire sizes, supporting maximum signal limits of 300 V and 2 A.

Field Installation Guidelines

Mount the compatible 1734-TBS or 1734-TOPS base onto a grounded 35 mm DIN rail prior to attaching the 1734-RTBS terminal block. Ensure the base mounting screws are tightened to a torque of 0.5 to 0.6 N m. Strip conductor insulation to the required length before inserting solid or stranded conductors (14 to 22 AWG) into the spring clamp terminals. Route field wiring in dedicated wiring trays away from high-voltage motor feeds to prevent noise interference. Maintain ambient operating conditions below 40 deg C and 80% non-condensing relative humidity at altitudes up to 1000 m above sea level without thermal derating.

Allen-Bradley 1734-RTBS POINT I/O Removable Terminal Block Assembly

The Allen-Bradley 1734-RTBS, also cataloged as the 1734-RTBS Terminal Block, operates as a dedicated hardware component for field wiring termination within POINT I/O 1734 platforms.

Hardware Specifications

Backplane Signal Termination and I/O Density Scaling

• The Allen-Bradley 1734-RTBS provides direct physical execution for signal distribution across EtherNet/IP deterministic networks.
• The 8-terminal spring-clamp layout facilitates rapid field wiring termination while maintaining I/O density scaling on POINT I/O slice platforms.
• Galvanic protection between logic-side processing and field wiring pathways is maintained via a 250 V continuous isolation voltage rating.
• Seamless firmware flash compatibility across primary PLC drops is preserved through passive electrical pass-through execution.

Frequently Asked Questions

Q: Which terminal base models are compatible with the 1734-RTBS spring-clamp assembly?

A: The 1734-RTBS is designed for installation on 1734-TBS and 1734-TOPS terminal base units.

Q: What wire sizes and electrical ratings are supported by the 1734-RTBS signal terminals?

A: The spring terminals accommodate 14 to 22 AWG (0.25 to 2.5 mm2) wire sizes, supporting maximum signal limits of 300 V and 2 A.

Field Installation Guidelines

Mount the compatible 1734-TBS or 1734-TOPS base onto a grounded 35 mm DIN rail prior to attaching the 1734-RTBS terminal block. Ensure the base mounting screws are tightened to a torque of 0.5 to 0.6 N m. Strip conductor insulation to the required length before inserting solid or stranded conductors (14 to 22 AWG) into the spring clamp terminals. Route field wiring in dedicated wiring trays away from high-voltage motor feeds to prevent noise interference. Maintain ambient operating conditions below 40 deg C and 80% non-condensing relative humidity at altitudes up to 1000 m above sea level without thermal derating.