General Electric GE IS200VAICH1CBR Turbine Control IS200

IS200VAICH1CBR Description

The IS200VAICH1CBR is a complex part of the Speedtronic Mark VI. The Mark VI Speedtronic line was deemed the state-of-the-art control for the GE turbines when it was issued. The IS200VAICH1CBR is named a VME card. Depend on what your system equipped with the VME can be placed in a thirteen or twenty-one slot card rack. With the IS200VAICH1C being a VME card and being considered the heart of the control system, the IS200VAICH1CBR uses many chips to control itself and to send out signals to the surrounding circuit boards. The chips are basically the brains of the circuit board and send signals to the rest of the circuit board and surrounding system that the IS200VAICH1CBR is connected to, in order for everything to run smoothly. The IS200VAICH1CBR uses many components to function. Diodes are one of the many components used for the circuit board to function. The diode is an electrical module with two terminals. If the energy flows through one end of the diode the energy will be allowed to pass through it. If energy flows through the opposite side of the diode it will be met with resistance, and not allowed to pass. The IS200VAICH1CBR comes furnished with interference suppressors. Seven small yellow ones and six large black ones. The IS200VAICH1CBR has a total of thirteen. The microchips range in size and how much information they can each hold. Please refer to the manuals for more detailed information.

Frequently Asked Questions about IS200VAICH1CBR

How much load resistance does IS200VAICH1CBR support?

When driving 20 mA outputs IS200VAICH1CBR supports up to 500 load resistance at the end of 1000 ft of #18 wire.

What are the LEDs on IS200VAICH1CBR?

IS200VAICH1CBR has three LEDs located on the top of IS200VAICH1CBR. These LEDs on IS200VAICH1CBR are indicated by RUN, FAIL, and STAT on IS200VAICH1CBR.

What is included in IS200VAICH1CBR's firmware?

Included in IS200VAICH1CBR's firmware is gas turbine compressor stall detection, which is executed at 200 Hz on IS200VAICH1CBR.

Which manual is used with IS200VAICH1CBR?

You can use Manual GEH-6421 with IS200VAICH1C. This manual is the Mark VI Turbine Control System Guide Manual. And though the manual is not a specific manual to IS200VAICH1CBR, the manual addresses VAIC boards and IS200VAICH1CBR in particular, starting on page 35 of the manual.

GE Others

IS200ACLEH EX2100 ACLE CARRIER CARD

IS200ACLEH1A EX2100 ACLE CARRIER CARD

IS200AVIFH BRIDGE INTERFACE

IS200AVIFH1A BRIDGE INTERFACE

IS200BAIAH PWM2/3 I/O BOARD

IS200BAIAH1B PWM2/3 I/O BOARD

IS200BICHH BRIDGE INTERFACE HIG

IS200BICHH1A BRIDGE INTERFACE HIG

IS200BICLH BRIDGE INTERFACE CARD

IS200BICLH1B BRIDGE INTERFACE CARD

IS200BICMH IGBT GATE DRIVER

IS200BICMH1A IGBT GATE DRIVER

IS200BICRH BRIDGE INTERFACE ROB

IS200BICRH1A BRIDGE INTERFACE ROB

IS200BLIGH BIC LAN INTERFACE-GE

IS200BLIGH1A BIC LAN INTERFACE-GE

IS200BPIAG BALANCE OF PLANT ANA

IS200BPIAG1A BALANCE OF PLANT ANA

IS200BPIBG PHASE LOGIC INTERFACE

IS200BPIBG1A PHASE LOGIC INTERFACE

IS200BPIHH BICH TO FOSB INTERFACE

IS200BPIHH1A BICH TO FOSB INTERFACE

IS200BPPH MK6 CARD

IS200BPPH2B MK6 CARD

IS200BPVC MAY BE MOTHERBOARD (3 NOS)

IS200BPVCG MAY BE MOTHERBOARD (3 NOS)

IS200BPVCG1BR1 MAY BE MOTHERBOARD (3 NOS)

IS200CABPG CONTROL ASM IGCT BACKPLANE

IS200CABPG1B CONTROL ASM IGCT BACKPLANE

IS200CPFPG GE SPEEDTRONIC / GE DRIVE SYSTEMS

IS200CPFPG1A GE SPEEDTRONIC / GE DRIVE SYSTEMS